Roof snow load in Massachusetts is set by town, not by one statewide number. The state building code assigns each city and town a ground snow load, and the roof design load is worked out from that figure. In the 10th Edition, town values run from 25 to 60 psf. To find yours, look up your town in the code table or call your local building department.
This guide explains what the numbers mean, how a ground value becomes a roof value, where to find the table, and how to handle a heavy storm on a roof you already own.
TL;DR
- Massachusetts has no single snow load. Each city and town has its own ground snow load (Pg) in the state building code, from 25 to 60 psf in the 10th Edition.
- Ground snow load is a baseline. Roof snow load depends on that baseline plus roof shape, slope, exposure, drifting and ice.
- Your town’s code table is the authority. Confirm the value, and any local rules, with your building department before a roof project.
- Flat and low-pitched roofs carry the most risk. Clear snow from the edge with a roof rake, leave a thin base layer, and stay away from utility wires.
- Wet snow is far heavier than dry snow, so depth alone tells you little.
Table of Contents
- Ground snow load vs. roof snow load
- How the code turns a ground value into a roof value
- Where to find the Massachusetts snow load map or table
- How heavy is snow, really?
- What increases snow loading on a roof
- What to do after a heavy snowfall
- When the roof itself needs work
- Plan your roof before the next storm
- A short checklist before you build, re-roof or add on
- FAQ
- Sources
Ground snow load vs. roof snow load
The two terms sound alike, but they measure different things.
Ground snow load is the typical weight of accumulated snow on open, unobstructed ground at a specific place, measured in pounds per square foot (psf). Building America’s guidance on managing snow loads defines it this way, drawing on the IRC, FEMA P-957 and IBHS.
Roof snow load is the load a roof structure is designed to carry. The same guidance says it is influenced by the ground snow load, the roof’s shape, slope and exposure, and the potential for drifting or ice buildup. A sheltered roof with a steep pitch will see less than a wide, flat, wind-exposed one in the same town.
So when someone says “Massachusetts requires 40 psf,” they usually mean the ground value for a town. The roof your rafters or trusses must handle is derived from it.
How the code turns a ground value into a roof value
The Massachusetts State Building Code (780 CMR) amends the base model code with its own snow provisions. Section 1604.11 says the ground snow load for each city and town is the value given in Table 1604.11, and section 1608.2 says design snow loads for roofs must be determined from that table.
Three details matter in practice:
- The table lists two numbers per town. According to the 10th Edition chapter, Table 1604.11 gives ground snow loads and minimum flat roof snow loads for each city and town.
- The larger value governs. Under the same chapter, the design flat roof snow load is the larger of the value calculated from the ground snow load (Pg) or the minimum flat roof snow load (Pf) listed for your town.
- Elevation can raise the number. Where the site elevation is higher than the mean elevation listed for the town, the ground snow load must be increased by 0.021 × (site elevation − mean elevation), according to the table notes. Hilltop lots in a town with big elevation swings are the usual case.
A worked example of the elevation rule
Say a town’s table lists a mean elevation of 600 feet and your lot sits at 800 feet. The difference is 200 feet. Multiply by 0.021 and you get 4.2 psf added to the table’s ground snow load. A 40 psf town becomes 44.2 psf at your address. The example is illustrative: use your own town’s mean elevation from the table notes and your surveyed site elevation.
Where to find the Massachusetts snow load map or table
People often search for a Massachusetts snow load map. The code itself uses a town-by-town table rather than a contour map, which is why the answer is a list of values.
Here is how to find your number:
- Open the state code chapter. Table 1604.11 in the 10th Edition, Chapter 16: Structural Design lists every city and town. Find your town alphabetically.
- Check which volume applies to your house. The chapter carries an exception: for ground snow load and basic wind speeds for R-3 one- and two-family dwellings of three stories or less, it refers you to the One- and Two-family Dwellings volume of 780 CMR. Most single-family homes fall under that residential volume, which has its own town snow load table. The two tables serve different building types, so confirm which one your inspector applies.
- Note the edition. The state updates its code periodically. The official copies of the regulations are obtained from the Secretary of the Commonwealth, and the 10th Edition is the one the research above reflects.
- Call the local building department. Towns can add local requirements, and the inspector is who signs off on your permit. Ask which table and which edition they use for your address.
The building department call takes five minutes and removes guesswork. If you are planning a re-roof, our Massachusetts roofing permit guide walks through what to expect at the permit counter.
How heavy is snow, really?
A psf number only makes sense when you can picture it. Depth is a poor guide because density varies so much. According to the Building America resource, one foot of heavy, wet snow can weigh as much as 21 psf, while one foot of light, dry snow may weigh about 3 psf.
That gap is the reason a modest-looking storm of wet coastal snow can stress a roof more than a bigger, fluffy one inland. It also explains why a rain event on top of snow is a concern: water soaks into the pack and adds weight without adding depth.
A rough comparison for a New England winter:
| Snow condition | Approximate weight per foot of depth |
|---|---|
| Light, dry powder | about 3 psf |
| Heavy, wet snow | up to about 21 psf |
These are the endpoints from the guidance above. Settled, rain-soaked or refrozen snow sits toward the heavy end.
What increases snow loading on a roof
The code value assumes a certain roof and exposure. Real roofs vary. These conditions push the actual load higher or concentrate it:
- Flat and low-pitched roofs. Mass.gov’s roof collapse guidance identifies these as the greatest risk for structural problems in heavy snow, because snow stays put instead of sliding off.
- Drifting. Wind piles snow against parapets, dormers, chimneys and where a lower roof meets a taller wall. The Building America guidance lists drifting among the influences on roof snow load.
- Ice accumulation. Ice dams and refrozen melt add dense weight at the eaves, and they trap water that can leak into the house.
- Clogged drains and gutters. On flat roofs, blocked drains let meltwater pond on top of the snow.
- Under-designed or altered structure. The same federal guidance notes that excess snow can deflect structural members and, in some cases, collapse under-designed structures. Additions, cut-in skylights and removed framing are where problems tend to hide.
If your house is older than the current code editions, it was likely framed to an earlier, sometimes lower value. That does not mean it is unsafe, but it is a reason to have a professional look at a sagging ridge or a ceiling that has started to crack under the roof.
What to do after a heavy snowfall
Mass.gov publishes practical steps for homeowners. In summary, the state recommends:
- Use a snow rake and pull snow down from the roof’s edge, working upward.
- Leave a base layer of about 2 to 3 inches so you do not damage the roofing.
- Keep gutters and drains clear.
- Stay clear of utility wires, and wear protective gear.
A few notes from the field. Raking from the ground is the safer approach. Climbing onto a snowy or icy roof is a different risk altogether, and for a steep or multi-story roof the sensible move is to hire a snow removal service rather than do it yourself. Never use sharp tools such as shovels with metal edges on shingles.
Warning signs inside the house
Call a licensed contractor or structural engineer promptly if you see any of these after a storm:
- Doors or windows that suddenly stick or will not latch.
- New cracks in drywall or plaster, especially near corners or across ceilings.
- Visible sagging of ceiling lines, or creaking and popping from the attic.
- Leaks that appear where there were none.
If you hear loud cracking or see ceilings bowing, leave the house and call 911.
When the roof itself needs work
Snow does most of its damage over several winters, not in one dramatic event. Slow leaks at flashing, lifted shingles and ice dam staining are early signals. Our guide to roof repair vs. replacement lays out how to judge which makes sense, and the roof replacement cost guide for Massachusetts helps you plan the budget.
A few things to ask any roofer about before a re-roof in a snowy town:
- Which snow load applies to your address, and whether the work touches framing that the building inspector will review.
- Ice and water protection along the eaves and in valleys.
- Ventilation and insulation in the attic, so heat does not escape and melt snow unevenly. Attic air sealing and insulation reduce the freeze and thaw cycle that feeds ice dams. If you are not sure where your home stands, a home energy audit shows where the heat is leaking.
- Flashing details at chimneys, dormers and walls where drifts form.
Perspective
After more than 40 years of working on New England homes, we see the same pattern every winter: the roofs that struggle are rarely the ones with a code problem on paper. They are the ones with a small issue that nobody addressed, such as a clogged valley, thin attic insulation, tired flashing or a patch job on top of a patch job.
We think the snow load number is worth knowing, and your building department is the right place to confirm it. But the better question for most homeowners is whether the roof system as a whole is ready for January. That means the shingles, the underlayment, the ventilation and the insulation working together.
As a family-owned company with more than 11,000 completed projects, we would rather walk your roof in October and explain what we see than meet you after a storm. A well-installed new roof with proper attic insulation is the most dependable way we know to take the stress out of a Massachusetts winter.
Jess
Plan your roof before the next storm
If your roof is near the end of its life, or last winter left stains on your ceiling, we can inspect it and walk you through your options. Bruin Corporation of Attleboro installs and replaces roofs, repairs them, and upgrades attic insulation for homeowners across Massachusetts and Rhode Island, and we offer financing options for larger projects.
Learn more about new roof installation and replacement, or if a storm has already done damage, see our storm damage repair service. Pricing is project-specific, so we quote after we see your roof.
A short checklist before you build, re-roof or add on
- Look up your town in Table 1604.11 and in the residential volume of 780 CMR if your home is a one- or two-family dwelling of three stories or less.
- Check your site elevation against the mean elevation listed for your town, and apply the 0.021 per foot adjustment if you are above it.
- Ask the building department whether your town has any local amendments.
- Identify roof features that create drifts: dormers, parapets, adjacent taller walls.
- Confirm that drains, gutters and valleys are clear before the first storm.
- Buy a roof rake and keep it where you can reach it.
FAQ
What is the roof snow load in Massachusetts?
There is no single value. The state building code gives each city and town a ground snow load, and in the 10th Edition the values range from 25 to 60 psf. The roof design load is calculated from your town’s number, and the code uses the larger of the calculated value or the town’s listed minimum flat roof snow load.
Is there a Massachusetts snow load map?
The code expresses snow load as a table by town rather than a map. Table 1604.11 in the state building code lists each city and town. Look up your town, then confirm with your local building department which table and edition they apply to your property.
Does my town’s snow load change with elevation?
It can. When your site is higher than the mean elevation listed for the town, the code adds 0.021 psf for every foot of difference, per the table notes. A hillside lot may therefore need a higher design value than a lot in the same town’s valley.
How much snow is too much for my roof?
Weight matters more than depth. A foot of heavy, wet snow can weigh as much as 21 psf, while a foot of light, dry snow may weigh about 3 psf, according to Building America. If you see sagging, sticking doors or new ceiling cracks, call a contractor or structural engineer.
Should I remove snow from my roof myself?
Only if you can do it safely from the ground. Mass.gov advises using a snow rake from the edge upward, leaving 2 to 3 inches of snow, and keeping away from utility wires. For steep or high roofs, hire a professional.
Sources
- Managing Snow Loads on Roofs and Decks, Building America Solution Center
- Chapter 16: Structural Design, 780 CMR 10th Edition, Mass.gov
- 780 CMR Chapter 16 structural design amendments, Mass.gov
- Roof Collapse and Snow Removal Safety Information, Mass.gov